Oil burner License Study guides, Class notes & Summaries
Looking for the best study guides, study notes and summaries about Oil burner License? On this page you'll find 103 study documents about Oil burner License.
Page 2 out of 103 results
Sort by
-
oil burner final exam questions and answers
- Exam (elaborations) • 5 pages • 2024
- Available in package deal
-
- $10.99
- + learn more
oil burner final exam questions and answers
-
Oil Burners State test Questions And Answers
- Exam (elaborations) • 3 pages • 2024
- Available in package deal
-
- $10.99
- + learn more
Oil Burners State test Questions And Answers How should an oil tank be supported? - answer-Ridgid non-combustible supports to prevent settling, sliding, or lifting 
 
What gauge wire is used on most oil burner circuits? - answer-14 gauge minimum 
 
What does intermittent or interrupted mean? - answer-Intermittent - Transformer stays on throughout the burner firing cycle 
 
Interrupted - Transformer drops out after flame is established 
 
Who approves oil burner installations? - answer-the A...
-
Oil burner test Questions And Answers
- Exam (elaborations) • 7 pages • 2024
- Available in package deal
-
- $10.99
- + learn more
Max safety timing on a primary control - answer-15 seconds 
 
Safety control circuits shall be - answer-2-wire, one side grounded, with nominal voltage not exceeding 150v 
 
Crankcase/used oil may only be used in - answer-Commercial/industrial setting. Or in a appliance specifically designed to do so. 
 
Oil burning appliance shall be how far from electrical panel and oil tank - answer-3 feet from panel, 5 feet from tank 
 
Flue gas exit of a chimney shall be Atleast - answer-3 feet above h...
-
Oil burner License Study Guide ( Massachusetts )Questions & Answers
- Exam (elaborations) • 10 pages • 2024
- Available in package deal
-
- $10.99
- + learn more
What are the 3 funtions of an Oil Burner nozzle? - answer-Atomize, Meter, Patter. 
 
What are the 2 voltage circuits of a primary control? - answer-Line & Low. 
 
What is the function of a fuse? - answer-Protect circuit. 
 
What is the High Limit cut out? - answer-Max safe Temp or Pressure setting. 
 
What is the High Limit cut in? - answer-Cut out minus Differential. 
 
What is the "Max" Lockout time for a burner with a 3 GPH Flow Rate? - answer-45 Seconds. 
 
What is the minimum stack ...
-
Oil Burners license test Questions & Answers
- Exam (elaborations) • 7 pages • 2024
- Available in package deal
-
- $10.99
- + learn more
The main function of the primary control is: - answer-Locking out on safety in the event of flame failure 
 
Power must be provided to an electric blower control board on terminals: - answer-L1 and L2 
 
Once a PSC motor starts - answer-The centrifugal switch turns off the electricity to the capacitor and the start windings 
 
Materials who's electrons are so loosely bound that they can be persuaded to move with very little pressure allowing electricity to flow are called - answer-Conductor...
Too much month left at the end of the money?
-
Oil burner's test questions 1-200 Exam Questions & Answers
- Exam (elaborations) • 21 pages • 2024
- Available in package deal
-
- $10.99
- + learn more
Oil burner's test questions 1-200 Exam Questions & AnswersIn an electric circuit for the wattage to remain the same if the voltage drops, the amperage must - answer-Increase 
 
Atomizing type burners were designed to burn which type of fuel - answer-Type 2 fuel oil 
 
Pour point problems with outside above ground fuel tanks can be partially relieved by - answer-Reducing the pour point of No. 2 fuel oil by blending it with No. 1 fuel oil. 
 
A fuel oil storage tank cannot be installed - answ...
-
Oil Burner License Exam Questions & Answers
- Exam (elaborations) • 27 pages • 2024
- Available in package deal
-
- $10.99
- + learn more
What is the first thing a tech should do when arriving at a no combustion call? - answer-Ask how many times the customer reset the unit. 
 
What is the best long term solution for preventing a clogged nozzle? - answer--Remove any underground storage tanks. 
-Install a quality oil filter. 
-Cut the suction line 10" above the tank outlet to prevent sludge. 
 
Hot water and steam valves are interchangeable. - answer-False 
 
When in the presence of a flame, a cad cell normally reads.. - answ...
-
Oil Burner License Questions With 100% Correct Answers.
- Exam (elaborations) • 24 pages • 2024
- Available in package deal
-
- $9.69
- + learn more
What is the first thing a tech should do when arriving at a no combustion call? - Answer-Ask how many 
times the customer reset the unit. 
What is the best long term solution for preventing a clogged nozzle? - Answer--Remove any underground 
storage tanks. 
-Install a quality oil filter. 
-Cut the suction line 10" above the tank outlet to prevent sludge. 
Hot water and steam valves are interchangeable. - Answer-False 
When in the presence of a flame, a cad cell normally reads.. - Answer-300-100...
-
Oil Burner License Exam Questions and Answers, Latest Updated 2024/2025 (Verified Answers)
- Exam (elaborations) • 20 pages • 2024
- Available in package deal
-
- $14.49
- + learn more
Oil Burner License Exam Questions and Answers, Latest Updated 2024/2025 (Verified Answers) What is the best long term solution for preventing a clogged nozzle? - Answer- -Remove 
any underground storage tanks. 
-Install a quality oil filter. 
-Cut the suction line 10" above the tank outlet to prevent sludge. 
Hot water and steam valves are interchangeable. - Answer- False 
When in the presence of a flame, a cad cell normally reads.. - Answer- 300-1000 ohms 
If a pump is used to bring oil to a l...
-
Oil Burner License Exam Questions and Answers, Latest Updated 2024/2025 (Verified Answers)
- Exam (elaborations) • 20 pages • 2024
- Available in package deal
-
- $14.99
- + learn more
Oil Burner License Exam Questions and Answers, Latest Updated 2024/2025 (Verified Answers) What is the first thing a tech should do when arriving at a no combustion call? - AnswerAsk how many times the customer reset the unit. 
What is the best long term solution for preventing a clogged nozzle? - Answer- -Remove 
any underground storage tanks. 
-Install a quality oil filter. 
-Cut the suction line 10" above the tank outlet to prevent sludge. 
Hot water and steam valves are interchangeable. - A...
$6.50 for your textbook summary multiplied by 100 fellow students... Do the math: that's a lot of money! Don't be a thief of your own wallet and start uploading yours now. Discover all about earning on Stuvia